Pixracer Autopilot

Codice prodotto PIXV1
Categoria PIXRACER
Marca POWER-HD
Disponibilità 4
Disponibilità altri pezzi previo ordine si
Tempistica di preparazione prevista 6 giorni lavorativi

Segnala ad un amico

Altre domande ?

 
pin it
Voto degli utenti (voti: 345)

Pixracer Autopilot

 

Come in foto compreso custodia Blu 

The Pixracer is the first autopilot of the new FMUv4 Pixhawk generation. It has Wifi built-in, comes with upgraded sensors and more flash. The final revision of this new design will likely consolidate on a single set of sensors (either ICM or MPU, both from Invensense).

  • Integrated Wifi telemetry and boot loading through ESP8266 (config and firmware)
  • Invensense ICM-20608 Accel / Gyro (4 KHz)
  • Invensense MPU9250 Accel / Gyro / Mag (4 KHz)
  • Honeywell HMC5983 magnetometer with temperature compensation
  • Measurement Specialties MS5611 barometer
  • JST GH connectors
  • microSD
  • Futaba S.BUS and S.BUS2 / Spektrum DSM2 and DSMX / Graupner SUMD / PPM input / Yuneec ST24
  • FrSky telemetry port
  • OneShot PWM out (configurable)

Main interfaces:

  • GPS (serial + I2C)
  • TELEM1
  • TELEM2
  • Wifi serial
  • FrSky Telemetry serial
  • Dronecode Debug connector (serial + SWD)

Pinouts

TELEM1, TELEM2+OSD ports

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) CTS (IN) +3.3V
5 (blk) RTS (OUT) +3.3V
6 (blk) GND GND

GPS port

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) I2C1 SCL +3.3V
5 (blk) I2C1 SDA +3.3V
6 (blk) GND GND

FrSky Telemetry / SERIAL4

Pin Signal Volt
1 (red) VCC +5V
2 (blk) TX (OUT) +3.3V
3 (blk) RX (IN) +3.3V
4 (blk) GND GND

RC Input (accepts PPM / S.BUS / Spektrum / SUMD / ST24)

Pin Signal Volt
1 (red) VCC +5V
2 (blk) RC IN +3.3V
3 (blk) RSSI IN +3.3V
4 (blk) VDD 3V3 +3.3V
5 (blk) GND GND

CAN

Pin Signal Volt
1 (red) VCC +5V
2 (blk) CAN_H +12V
3 (blk) CAN_L +12V
4 (blk) GND GND

POWER

Pin Signal Volt
1 (red) VCC +5V
2 (blk) VCC +5V
3 (blk) CURRENT +3.3V
4 (blk) VOLTAGE +3.3V
5 (blk) GND GND
6 (blk) GND GND

SWITCH

Pin Signal Volt
1 (red) SAFETY GND
2 (blk) !IO_LED_SAFETY GND
3 (blk) VCC +3.3V
4 (blk) BUZZER- -
5 (blk) BUZZER+ -

Dronecode debug port (JST SM06B connector)

Pin Signal Volt
1 (red) VCC TARGET SHIFT +3.3V
2 (blk) CONSOLE TX (OUT) +3.3V
3 (blk) CONSOLE RX (IN) +3.3V
4 (blk) SWDIO +3.3V
5 (blk) SWCLK +3.3V
6 (blk) GND GND

Gli utenti registrati possono condividere la loro esperienza avuta con questo prodotto/servizio. Registrati per accedere a tutti i benefici riservati agli utenti registrati o clicca su login se sei già registrato.